T-Force Wheels 890C01 Center Cap Identification Guide
Shopping for a 890C01 center cap is not a “looks close enough” decision.
The current WheelCenterCaps.com record identifies this as new replacement item wheel center cap from T-Force Wheels in Silver. The listing is the source for those details; anything it does not state stays unclaimed.
Here is the blunt truth: a similar-looking part is not a confirmed match.
View the current T-Force Wheels 890C01 center cap listing
The known facts in one place
| Product | Wheel Center Cap |
|---|---|
| Brand / manufacturer | T-Force Wheels |
| Part number(s) listed |
890C01, 89-9586T, S1304-07
|
| Store SKU | 890C01 Silver |
| Finish / color | Silver |
| Attachment style | Snap-in |
| Sold as | Sold individually |
| Condition | New replacement item |
890C01 and the other listed identifiers
The current product record tells shoppers to verify 890C01, 89-9586T, S1304-07. Do not silently drop a suffix or choose only the shortest number because it is easier to type. Record every identifier shown on your original item, then compare the complete set with the live listing.
These numbers appear together in this listing. That does not prove that every item carrying only one of them is universally interchangeable. The physical design still has to match.
The listed finish is Silver
The product record describes the finish as Silver. That wording matters when you are replacing one item instead of a complete set. “Black” is not specific enough when gloss, matte, satin and mixed-finish parts can look very different beside one another.
Compare the live product image with the surviving parts in neutral daylight. Also compare the logo and any decorative details that are actually visible. Lighting, dust and years of exposure can make the same finish photograph differently.
What the listing says about attachment
The supplied product record lists the attachment style as Snap-in. That is the mounting claim supported by this record. It does not supply unstated clip dimensions, fastener sizes, hole spacing or installation torque.
Compare the original item and the current product photos before installation. Nothing should need to be forced into place, and a fastener that immediately binds is a reason to stop—not to reach for a power tool.
How many pieces does the listing describe?
The product record says Sold individually. Quantity language matters: a product photograph may show more than one angle or component without promising that every pictured item is included.
What this product record does not establish
The supplied listing does not state an exact cap diameter, height or depth, the material or whether mounting hardware is included. Those are reasons to verify—not invitations to guess.
If one of those details decides fitment, compare the original item directly with the live product photos or contact WheelCenterCaps.com before ordering.
Use a side-by-side match, not a memory test
If one original cap survives, it is your best evidence. Clean only enough grime to read the markings, photograph 890C01, 89-9586T, S1304-07 and keep the cap nearby while reviewing the listing. Compare the face and back under similar light. Do not sand, reshape or remove clips merely to make a questionable replacement appear closer.
One correct replacement is the goal, not the largest list of possible interchanges. Unless the current record explicitly identifies another code, treat outside aliases as leads that still require a physical match. This keeps an unverified marketplace cross-reference from becoming a fitment claim.
Stop condition: if the complete identifier or the rear design disagrees, do not install the part. Contact T-Force Wheels support or the seller with the photos you collected.
Make the physical comparison reproducible
Compare sheen, not only color. The record uses Silver. Look at how light rolls across the surface and how the logo or accents contrast with it. Dust and aging can dull an original, so finish is best used after the identifier and mechanical design agree—not as a shortcut around them.
Control the camera angle. A straight-on face photo helps compare logos and outline; a straight-on rear photo shows the retention layout; a low side view reveals the profile. Take those three views of the original before opening the T-Force Wheels listing. Matching angles make genuine differences easier to see and prevent perspective from turning a shallow part into a tall one.
Name every measurement. “Eight inches” is not useful unless both people know whether it means the face, the rear skirt or a mounting circle. Label the start and end points in your photo and keep the ruler in the same plane as the feature. The supplied record should not be supplemented with an unlabeled number from a different listing.
Decide whether one replacement will look intentional. A new Silver part may sit beside three weathered originals. That cosmetic difference does not establish bad fitment, but it can affect whether a single or full-set purchase meets your goal. Confirm Sold individually before assuming the listing solves either option.
Clean gently for identification. Use a soft cloth to expose molded or printed marks on the old wheel center cap. Aggressive scraping can remove a sticker, flatten shallow lettering or alter the edge you need to compare. The objective is readable evidence, not a showroom finish. Photograph the markings as soon as they become legible.
Preserve the suffix. The end of a part number is easy to dismiss as a color code or revision, yet this record does not authorize dropping it. Keep every letter and digit attached to 890C01 while comparing offers. If another page shows the same base with a different ending, treat it as a separate candidate until the photos and listing facts prove otherwise.
The cap fits the wheel—not the vehicle badge
A vehicle year, make and model cannot identify an aftermarket wheel center cap by itself. The same truck, SUV or car can wear factory wheels, several aftermarket wheel models or a different wheel on each trim package.
Use vehicle information as background only. The stronger evidence is the complete part number, the wheel itself and a physical comparison of the original cap with the current listing.
A matching logo is only the first check
Many wrong-cap orders begin with a convincing front view. A logo, outline or finish may look right while the back of the cap uses a different shell profile, retention layout or mounting position. The supplied record does not establish that a similar-looking cap with another part number is interchangeable with this one.
Set the original cap beside the live product photos and compare both sides in the same order. Start with the complete molded or printed number. Then check the face, edge profile and every visible point where the cap meets the wheel. If one photo hides the feature that decides the match, treat that detail as unresolved.
Also account for ordinary wear. Sun exposure, brake dust, cleaners and scratches can change how an older cap looks without changing its identity. Use finish as supporting evidence, but let the complete identifier and physical design carry more weight.
Document the original before making the match
A few clear photos and notes are more useful than trying to remember a part after it has been removed. Clean only enough dirt to reveal the identifier and attachment details; do not grind, scrape or polish away markings. Work in even light and keep the camera square to the item so perspective does not exaggerate its shape.
- Capture the identifier. Photograph the complete number in focus, including any prefix, suffix, dash or space. Write it down exactly as shown.
- Photograph both sides. Take a straight-on face image and a clear rear view. Add close-ups of retention points, holes, tabs or other features that are actually present.
- Record comparison measurements. When a measurement is needed, note where it starts and ends and which tool you used. A number without consistent reference points is easy to misread.
- Save the listing evidence. Compare your notes with the current title, description and photos at checkout. Product offers can change, so confirm quantity and included pieces on the page you are buying from.
If the original item is missing, do not replace it with a guess based on the vehicle alone. Record the wheel brand, any wheel model or casting numbers you can actually see, and clear photos of the mounting area. Send that evidence when asking for help; it gives the seller something specific to evaluate.
A no-guesswork identification checklist
-
Read every identifier. Match
890C01,89-9586T,S1304-07, the SKU where useful and every number visible on the original cap. - Compare the front. Check the outline, logo, finish and any decorative details shown in the live listing.
- Compare the back. Match the shell profile, retention points and mounting locations without assuming a similar face means the same cap.
- Measure consistently. If dimensions are not published, measure the surviving cap and ask the seller to confirm the same points on the replacement.
- Confirm the offer. Verify finish, quantity and included hardware on the current product page before checkout.
Frequently asked questions
Will 890C01 fit my vehicle?
Only if the wheel on that vehicle uses the matching center-cap design. Vehicle year, make and model alone are not enough.
Which numbers should I match?
The current record lists 890C01, 89-9586T, S1304-07 and store SKU 890C01 Silver. Match the complete identifiers and product design instead of relying on one shortened number.
What finish does the listing identify?
The supplied product record lists Silver. Compare the live image with the parts already on the wheel before ordering one replacement.
How does it attach?
The listing identifies Snap-in. No unstated mounting dimensions or fastener specifications are assumed here.
Is the listing for one piece or a set?
The product record says Sold individually.
Is mounting hardware included?
The supplied record does not establish that. Do not assume screws, bolts, retainers or tools are included unless the live product page explicitly says so.
What are the dimensions?
No exact diameter, height or depth is stated in the supplied record. Measure the original cap consistently and request confirmation rather than borrowing a measurement from another listing.
Shop the correct replacement
Match the identifiers first, the physical design second and the finish third. That order is faster than processing a return.